Professional hvac installation services for homes and businesses in Edgewood and surrounding Kentucky communities.
A complete HVAC installation from KIC Refrigeration in Edgewood, KY addresses every element in the comfort chain, from the air handler and condensing unit to the thermostat, ductwork, and filtration system. We ensure proper airflow balance, verified refrigerant charge, tested safety controls, and code-compliant operation before turning the system over to you.
Properties throughout Edgewood (pop. 8,567) face unique demands when it comes to hvac installation. Kentucky heating loads, cooling calculations, and the insulation levels and duct configurations found in Edgewood homes all influence the approach we take. KIC Refrigeration tailors every hvac installation project to the conditions your property actually faces — no generic solutions.
Choosing the right contractor for hvac installation in Edgewood, KY makes all the difference between efficient comfort and a system that short-cycles. KIC Refrigeration uses Manual J load calculations, installs to manufacturer specifications, and backs every project with a warranty. Call (866) 858-2961 to schedule your free assessment.
How our NATE-certified technicians deliver quality hvac installation results from start to finish.
Our Edgewood estimator walks your property room by room — measuring square footage, checking insulation levels, assessing window area, and inspecting existing ductwork and electrical service. We input all variables into a Manual J load calculation to determine your exact heating and cooling requirements in BTU.
Based on load calculations and your priorities — efficiency, noise level, budget, zoning — we recommend specific equipment and provide a detailed written proposal covering equipment model numbers, SEER2/AFUE ratings, installation scope, warranty, and total cost.
KIC Refrigeration installs HVAC systems in Edgewood, KY to the highest standards. We set equipment on level, vibration-isolated mounting, braze all refrigerant connections with nitrogen flowing, pressure test with dry nitrogen, evacuate to below 500 microns, charge by weight, seal all duct connections with mastic, and verify gas piping sizing and connections.
Our Edgewood technician commissions the system by verifying superheat, subcooling, temperature split, static pressure, and gas pressure in heating mode. We program the thermostat, register your manufacturer warranty, label the electrical panel, and walk you through operation and maintenance.
Transparent answers about hvac installation from our certified technicians.
Complete HVAC installation in Edgewood ranges from $7,000 to $15,000 for a mid-efficiency furnace and AC combination — typically an 80 percent AFUE furnace paired with a 14.3 to 16 SEER2 condenser. High-efficiency systems with variable-speed blowers and two-stage or variable-speed compressors run $12,000 to $22,000 but deliver significantly lower operating costs and qualify for federal tax credits. Heat pump systems fall between $5,000 and $18,000 depending on whether the system is single-stage, variable-speed, or a dual-fuel configuration. Ductwork modifications or new duct runs add $1,000 to $5,000. KIC Refrigeration provides detailed written proposals for Edgewood homeowners with every cost itemized and no hidden fees.
Yes, substantially. Replacing a 10 SEER air conditioner with a 16 SEER2 unit reduces cooling energy consumption by approximately 38 percent. Upgrading from an 80 AFUE furnace to a 96 AFUE condensing furnace saves 16 cents of every heating dollar — the old furnace sends 20 cents up the flue while the new one captures it. Combined with proper installation practices — correct refrigerant charge verified by superheat and subcooling, proper static pressure and airflow at 400 CFM per ton, sealed duct connections, and a programmable thermostat — a new system typically saves Edgewood homeowners $600 to $1,800 per year depending on home size, usage patterns, and local energy rates.
Correct HVAC system sizing is determined by a Manual J residential load calculation — the ACCA industry standard — that accounts for your home square footage, ceiling height, insulation R-values, window area and U-factor, air infiltration rate, duct losses, occupancy, and the local KY winter and summer design temperatures. As a rough reference, a well-insulated 2,000-square-foot home in Edgewood typically needs a 2.5 to 3.5 ton system, while a poorly insulated home of the same size may need 4 tons. KIC Refrigeration never estimates by rule of thumb — we run a proper calculation for your specific Edgewood home to avoid oversizing, which causes short cycling, high humidity, and premature compressor wear.
Yes. KIC Refrigeration pulls all required mechanical, electrical, and gas permits for every HVAC installation in Edgewood, KY. We prepare the permit application with equipment specifications and installation plans, pay the permit fee, schedule the inspection with the local building department, meet the inspector on-site, and ensure the installation passes all applicable mechanical code requirements. A building permit is not optional — it is required by law in most Edgewood jurisdictions, and an unpermitted installation can void the manufacturer equipment warranty, create title problems when selling the home, and may not be covered by homeowner insurance if an HVAC failure causes property damage. KIC Refrigeration includes permitting in every installation project.
Our reputation is built on certified technicians, honest pricing, and results that last.
"Mini split repair was done right the first time. The outdoor unit had a refrigerant leak and they found it, fixed it, and recharged the system same day."
"Our AC went out on the hottest day of the year and they had someone here within two hours. Fixed it fast and explained everything clearly."
"Called for an emergency AC repair on a Friday evening fully expecting to wait until Monday. They came out that same night. Cannot say enough good things."